RCX H2205 (V2) 2633KV Multirotor Outrunner Brushless Motor (Motion Balanced)

KR-MTC0069

New

This H2205 stands between 1806 and 2206 motor, for those who needs higher thrust than 1806 motor but less weight than 2206.

16 Items

Ready Stock

Rp 175.000,00

This H2205 stands between 1806 and 2206 motor, for those who needs higher thrust than 1806 motor but less weight than 2206. This 2633KV is suitable for both

  • 4 inch propeller on 3-4S
  • 5 inch propeller on 3-4S
    • if it is too hot with 4S + 5040/5045, then you may need to change it back to 5030.

It assembled with Imported NMB Bearing and Copper Wire to maintain the quality. The motor has been balanced by Motion Balancing Machine so you will see the colored balancing mud in the motor. There are lots of brands who claimed their motors are balanced but in fact it is only static balanced (this means just to filter the highly imbalanced CNC out), its balancing quality is far away from real Dynamic Balancing. If you do not see the balancing mud inside almost all motors, that means their "balanced" word is just a joke. Be Smart & Buy Smart!

Dynamic balancing is the most time consuming part when manufacturing a motor so factories don't like to balance the motors due to saving of labor work. RCX always cannot catch up the supply demand due to this reason (production quantity is limited by the balancing work). If a factory can supply heaps of motors to the market, do you think their motors are balanced well? If RCX does not need to balance the motor, the production would be much faster.


Quality Motor Best for 170-350 frames.

Specification

  • Model: H2205-4
  • KV: 2633KV
  • Weight: Approx. 24-25g (net weight included long AWG cables)
    • you can lower the weight if you shorten the long AWG cables.
  • AWG Cable: 15cm
  • Prop Shaft Diameter: 5mm (CW)
  • Stator Diameter: 22mm
  • Stator Length: 5mm
  • Shaft Diameter: 3mm
  • Configuration: 12N14P
  • Motor Dimensions: Φ26.6*15.3mm
  • ldle Current: 0.86A @ 10V
  • Internal Resistance: 0.081Ω
  • Suitable ESC: 10-30A (depends on the propeller and battery you use)
    • HobbyWing's XRotor works pretty well with H2205 motor so it is recommended especially the XRotor 20A is small in size as small as some 10A-12A ESC.
    • Since SimonK and BLHeli might shutter during high RPM on small props (eg. 5030). So if you plan to drive the motor hard, please consider to get XRotor 20A or 40A because XRotor was tested at high RPM without any sync issue.
  • Suitable Battery: 3-4S Li-Po (refer to thrust test table and videos)

Maintenance Parts
Bearing and motor shaft are common consumable parts of a motor. You are recommended to replace a new one from time to time after a period of flight time. Replacement of bearings and motor shaft could sometime fix mirror issues. It is better for you to keep some for spare.

Package Included

  • 1 x RCX H2205-6 2633KV Micro Outrunner Brushless Motor
  • 1 x Hex Locknuts M5 (Slip-Resistant) - CW
  • 1 x Circle Plate
  • 1 x Set of M3*5 Screw

Notice: This question "my new motor is hard to turn by finger, it is not smooth so it is defective!" has been asked many times. Please click here for the answer. We are so tired to answer this question by email, please read it before you purchase.

No customer comments for the moment.

Write a review

RCX H2205 (V2) 2633KV Multirotor Outrunner Brushless Motor (Motion Balanced)

RCX H2205 (V2) 2633KV Multirotor Outrunner Brushless Motor (Motion Balanced)

This H2205 stands between 1806 and 2206 motor, for those who needs higher thrust than 1806 motor but less weight than 2206.

Top